59.060.30 (Mineral and metal fibres) 标准查询与下载

ASTM E2016-11 工业纺织金属丝布标准规格

1.1 This specification covers industrial woven wire fabric, referred to as wire cloth, for general use including the separation of particles. Wire cloth can be made of any primary metal or metal alloy wire that is suitable for weaving. This specification does not apply to the following special types of wire cloth: filter cloth or dutch weave (see Appendix X1), fourdrinier and cylinder cloth, galvanized hardware cloth, insect wire screening, spiral weave wire cloth, testing sieve cloth, or welded wire cloth. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Industrial Woven Wire Cloth

ASTM E2016-06 工业金属丝筛布的标准规范

1.1 This specification covers industrial woven wire fabric, referred to as wire cloth, for general use including the separation of particles. Wire cloth can be made of any primary metal or metal alloy wire that is suitable for weaving. This specification does not apply to the following special types of wire cloth: filter cloth or dutch weave (see ), fourdrinier and cylinder cloth, galvanized hardware cloth, insect wire screening, spiral weave wire cloth, testing sieve cloth, or welded wire cloth.1.2 The values stated in inch-pound units shall be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Industrial Woven Wire Cloth

ASTM D299/D299M-04(2009)e1 石棉纱线的标准规范

1.1 This specification covers asbestos yarns having a minimum of 75 % asbestos fiber by mass, excluding the mass of other inorganic reinforcing strands which may be present. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 Warning—Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysoltile asbestos, refer to “Safe Use of Chrysotile Asbestos: A Manual on Preventive and Control Measures.” 1.4 The following safety hazards caveat pertains only to the test methods, Section 13, described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 1.3 for a specific safety hazard statement.

Standard Specification for Asbestos Yarns

ASTM D299-04e1 石棉纱的标准规范

1.1 This specification covers asbestos yarns having a minimum of 75 % asbestos fiber by mass, excluding the mass of other inorganic reinforcing strands which may be present.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 Warning-Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysoltile asbestos, refer to "Safe Use of Chrysotile Asbestos: A Manual on Preventive and Control Measures."1.4 The following safety hazards caveat pertains only to the test methods, Section , described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 1.3 for a specific safety hazard statement.

Standard Specification for Asbestos Yarns

ASTM D299-04 石棉纱的标准规范

1.1 This specification covers asbestos yarns having a minimum of 75 % asbestos fiber by mass, excluding the mass of other inorganic reinforcing strands which may be present.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The following safety hazards caveat pertains only to the test methods, Section 13, described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Asbestos Yarns

ASTM D299-00 石棉纱的标准规范

1.1 This specification covers asbestos yarns having a minimum of 75% asbestos fiber by mass, excluding the mass of other inorganic reinforcing strands which may be present. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 The following safety hazards caveat pertains only to the test methods, Section 13, described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Asbestos Yarns

ASTM E2016-99e1 工业纺织金属丝布规范

1.1 This specification covers industrial woven wire fabric, referred to as wire cloth, for general use including the separation of particles. Wire cloth can be made of any primary metal or metal alloy wire that is suitable for weaving. This specification does not apply to the following special types of wire cloth: filter cloth or dutch weave (see Appendix X1), fourdrinier and cylinder cloth, galvanized hardware cloth, insect wire screening, spiral weave wire cloth, testing sieve cloth, or welded wire cloth.1.2 The values stated in inch-pound units shall be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Industrial Woven Wire Cloth

ASTM E2016-99(2004)e1 工业纺织金属丝布规范

1.1 This specification covers industrial woven wire fabric, referred to as wire cloth, for general use including the separation of particles. Wire cloth can be made of any primary metal or metal alloy wire that is suitable for weaving. This specification does not apply to the following special types of wire cloth: filter cloth or dutch weave (see Appendix X1), fourdrinier and cylinder cloth, galvanized hardware cloth, insect wire screening, spiral weave wire cloth, testing sieve cloth, or welded wire cloth.1.2 The values stated in inch-pound units shall be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Industrial Woven Wire Cloth

ASTM E2016-99 工业纺织金属丝布规范

1.1 This specification covers industrial woven wire fabric, referred to as wire cloth, for general use including the separation of particles. wire cloth can be made of any primary metal or metal alloy wire that is suitable for weaving. This specification does not apply to the following special types of wire cloth: filter cloth or dutch weave (see Appendix X1), fourdrinier and cylinder cloth, galvanized hardware cloth, insect wire screening, spiral weave wire cloth, testing sieve cloth, or welded wire cloth. 1.2 The values stated in inch-pound units shall be regarded as the standard. The values given in parentheses are information only.

Standard Specification for Industrial Woven Wire Cloth

ASTM D2590/D2590M-98(2011)e1 温石棉取样的标准试验方法

Sampling and conditioning are equally as important as testing. The reliability of the test results depends primarily upon how well the specimens tested represent the true character and condition of the lot of asbestos fiber. Much care and effort are required to be sure that all the sampling operations are systematic or at random and are representative. Failure to provide a test specimen that accurately represents the lot from which it is drawn will produce misleading test results regardless of the accuracy and the precision of the test method.1.1 This test method covers procedures for taking a composite or a master composite sample, at the mine or at the factory or from a consignment, of a lot of milled asbestos fiber used as raw material in the chrysotile asbestos industry, conditioning this sample and reducing it in quantity through a series of steps to provide a relatively small test specimen of loose asbestos fibers, representative of the lot and suitable for the determination of a single property. 1.2 This sampling method is suitable for taking test specimens of chrysotile asbestos for Test Methods: C1119, C1120, C1121, C1122, C1123, C1124, C1125, C1162, D1118, D2589, D2752, D2946, D2947, D2985, D2987, D3639, D3752 and D3880. 1.3 Test Method D3879 covers the sampling of amphibole asbestos fibers. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. ^REFERENCE: ASTM Standards: C1119 Test Method for Vacuum Drainage of Asbestos-Cement Mixes

Standard Test Method for Sampling Chrysotile Asbestos

ASTM D2590-98(2002) 温石棉取样的试验方法

1.1 This test method covers procedures for taking a composite or a master composite sample, at the mine or at the factory or from a consignment, of a lot of milled asbestos fiber used as raw material in the chrysotile asbestos industry, conditioning this sample and reducing it in quantity through a series of steps to provide a relatively small test specimen of loose asbestos fibers, representative of the lot and suitable for the determination of a single property.1.2 This sampling method is suitable for taking test specimens of chrysotile asbestos for Test Methods: C 1119, C 1120, C 1121, C 1122, C 1123, C 1124, C 1125, C 1162, D 1118, D 2589, D 2752, D 2946, D 2947, D 2985, D 2987, D 3639, D 3752 and D 3880. 1.3 Test Method D 3879 covers the sampling of amphibole asbestos fibers.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Sampling Chrysotile Asbestos

ASTM D2590-98(2006) 温石棉取样的标准试验方法

1.1 This test method covers procedures for taking a composite or a master composite sample, at the mine or at the factory or from a consignment, of a lot of milled asbestos fiber used as raw material in the chrysotile asbestos industry, conditioning this sample and reducing it in quantity through a series of steps to provide a relatively small test specimen of loose asbestos fibers, representative of the lot and suitable for the determination of a single property.1.2 This sampling method is suitable for taking test specimens of chrysotile asbestos for Test Methods: C 1119, C 1120, C 1121, C 1122, C 1123, C 1124, C 1125, C 1162, D 1118, D 2589, D 2752, D 2946, D 2947, D 2985, D 2987, D 3639, D 3752 and D 3880. 1.3 Test Method D 3879 covers the sampling of amphibole asbestos fibers.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Sampling Chrysotile Asbestos

ASTM D2590-98(2002)e1 温石棉取样的试验方法

1.1 This test method covers procedures for taking a composite or a master composite sample, at the mine or at the factory or from a consignment, of a lot of milled asbestos fiber used as raw material in the chrysotile asbestos industry, conditioning this sample and reducing it in quantity through a series of steps to provide a relatively small test specimen of loose asbestos fibers, representative of the lot and suitable for the determination of a single property.1.2 This sampling method is suitable for taking test specimens of chrysotile asbestos for Test Methods: C 1119, C 1120, C 1121, C 1122, C 1123, C 1124, C 1125, C 1162, D 1118, D 2589, D 2752, D 2946, D 2947, D 2985, D 2987, D 3639, D 3752 and D 3880. 1.3 Test Method D 3879 covers the sampling of amphibole asbestos fibers.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Sampling Chrysotile Asbestos

ASTM D2590-98(2006)e1 温石棉取样的试验方法

1.1 This test method covers procedures for taking a composite or a master composite sample, at the mine or at the factory or from a consignment, of a lot of milled asbestos fiber used as raw material in the chrysotile asbestos industry, conditioning this sample and reducing it in quantity through a series of steps to provide a relatively small test specimen of loose asbestos fibers, representative of the lot and suitable for the determination of a single property.1.2 This sampling method is suitable for taking test specimens of chrysotile asbestos for Test Methods: C 1119, C 1120, C 1121, C 1122, C 1123, C 1124, C 1125, C 1162, D 1118, D 2589, D 2752, D 2946, D 2947, D 2985, D 2987, D 3639, D 3752 and D 3880. 1.3 Test Method D 3879 covers the sampling of amphibole asbestos fibers.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Sampling Chrysotile Asbestos

ASTM D1571-95(2004) 石棉布的标准规格

1.1 This specification covers woven asbestos cloth having a minimum of 75 % asbestos fiber by weight, excluding the mass of other inorganic reinforcing strands which may be present.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The following safety caveat pertains only to the test methods portion, Section , described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Woven Asbestos Cloth

ASTM D1118-95(2004) 石棉纤维和石绵纺织品磁性率的标准试验方法

1.1 This test method covers the procedure for the determination of the magnetic rating of asbestos fiber and asbestos textile products. This test method is used primarily for testing asbestos insulating materials.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Magnetic Rating of Asbestos Fiber and Asbestos Textiles

ASTM D375-95(1999) 压敏胶带的断裂强度和伸长率的标准测试方法

1.1 This specification covers asbestos roving having a minimum of 75 mass % asbestos fiber, excluding the mass of other inorganic reinforcing strands which may be present. 1.2 The following safety hazards caveat pertains only to the test methods, Section 13, described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Asbestos Roving

ASTM D1118-95(2004)e1 石棉纤维和石绵纺织品磁性率的标准试验方法

1.1 This test method covers the procedure for the determination of the magnetic rating of asbestos fiber and asbestos textile products. This test method is used primarily for testing asbestos insulating materials.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 Warning-Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysoltile asbestos, refer to "Safe Use of Chrysotile Asbestos: A Manual on Preventive and Control Measures."1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific safety hazard, see 1.3.

Standard Test Method for Magnetic Rating of Asbestos Fiber and Asbestos Textiles

ASTM D1118-95(2004)e2 石棉纤维和石棉织物磁参数的标准测试方法

This test method for the determination of magnetic rating is considered satisfactory for acceptance testing of commercial shipments of asbestos fibers, papers, felts, yarns, rovings, textile products, rigid sheet products, and granular or powdered products. Magnetic rating is one of the measurements used for determining the suitability of an asbestos material for electrical insulation. The electrical insulating properties of asbestos materials vary inversely with the magnetic rating. Therefore, a low magnetic iron content is required for good electrical insulating. The types of asbestos textiles classified by magnetic rating are described in Specification D 2100. 1.1 This test method covers the procedure for the determination of the magnetic rating of asbestos fiber and asbestos textile products. This test method is used primarily for testing asbestos insulating materials.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 Warning-Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysoltile asbestos, refer to "Safe Use of Chrysotile Asbestos: A Manual on Preventive and Control Measures."1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific safety hazard, see 1.3.

Standard Test Method for Magnetic Rating of Asbestos Fiber and Asbestos Textiles

ASTM D315-95(1999) 机织石棉带标准规范

1.1 This specification covers woven asbestos tape having a minimum of 75% asbestos fiber by weight, excluding the weight of other inorganic reinforcing strands that may be present. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 The following safety hazards caveat pertains only to the test methods, Section 13, described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Woven Asbestos Tape